International Truck Engine Family VT 365 description of the catalogue:

Master Service Information (Engine Group)
INTERNATIONAL® VT 365 DIESEL ENGINE
VT-365 Diesel Engine Diagnostics (2002)
VT 365 Diesel Engine - 2004 Model Year

Vehicle Recall Campaigns
ENGINE CALIBRATION on Certain 1652SC, 3200, 4100, 4200, RXT, TSV, 3300, BE, CE, HC, and SFC Models Built 12/4/01 thru 12/14/09 with a VT 365 Engine Having Calibration PAN2PVR0, PAN2PVR1, or PAN2PWR0
IDM FUSE BLOCK on Certain INTERNATIONAL® 3200, 3300, and IC Bus BE, CE, HC, RE Models Built 9/21/01 thru 12/31/07 with an INTERNATIONAL® VT-365 engine
Inspecting and Replacing the Fuel Injector Control Module on 3200 and 4200 Models Built From 09/21/01 through 06/26/02 With VT 365 Engines

Authorized Field Change (AFC) Letters
Bendix Air Compressor on Certain MaxxForce® 7 and VT 365 Engines
Improved Engine Calibration for Certain Bus and Stripped Chassis Models Built with VT 365 Engines
Low Coolant Sensor Installation and Cooling System 'Hot' Pressure Testing
Low Coolant Sensor Installation and Cooling System 'Hot' Pressure Testing
Engine Air Management System Upgrade
High Pressure Pump Snap to Connect Fitting Update
Hard Start/No Start or Excessive Smoke After Start
Engine Reconfiguration and New Exhaust Emission Label for VT 365 Engines, ESN 0112360 through 141748, with Feature Code 12990 used in Truck Models Built Between February 10, 2004 and September 7, 2004

Technical Service Information (TSI) Letters
Engine and Transmission ECU Clean Power Connector Checks To Correct Intermittent Operation
Release of a new Oil Cooler Cover Service Kit
New ECM calibration for the Engine Warning and Protection System (EWPS) and New IDM Calibration
Remote Fuel/Water Separator Installation With 150 Watt Electric Heater, Water In Fuel Sensor And Fuel Restriction Switch
Turbocharger Unison Ring
Installation of Lower Crankcase Seals
Revised Cylinder Head Flatness Check
Prevention of Objects and Debris from Falling into Intake Ports during Removal and Installation of Intake Manifold
Protecting Removed Hydraulically Actuated Fuel Injectors
Cylinder Head Service Kit Identification
Valve Train Service Kit
Lube Oil Recommendations for International® Diesel Engines
Flat Pulley and Belt Kit to Eliminate Belt Squeal
Sensor O-ring Kit for CMP or CKP Applications
Emission Calibration Conversion from Highway to Non-road (off-road)
Flywheel Housing Adapter Hub Assembly Changes
2006 Model Year Changes for VT 365 Diesel Engines
In-chassis Service Procedure: Removal and Installation of Branch Tube Assembly
Water Pump And Air Compressor Drive Pulley
Turbocharger and Mounting Assembly Service Kits
Release of New Air Compressor and Elbow Service Kit
Cylinder Head Kit
Turbocharger Solenoid Valve Kits
Pushrod Assembly
New Crankcase-to-Head Tube Assembly and Injection Control Pressure (ICP) Adapter/Plug Kit for Diagnostics
Exhaust Manifold Leak
Low Injection Control Pressure (ICP) Test
Convert The International® VT 365 2004 Model Year Engine Emission Calibration (Highway Use) To Non-Road (Off-Road) Engine Emission Calibration
Bolt Retainers Removed from Branch Tube Adapter for High-Pressure Oil Pump
Convert the International® VT 365 on-road engine emission calibration to off-road engine emission calibration
International® VT 365 Upper Oil Pan Assembly
Performance Specifications for Model Year 2002 and 2003 International® VT 365 Engine Applications
Exhaust Gas Recirculation (EGR) Diagnostics for Model Year 2004 International® VT 365 Engine Applications
Production and service calibration history and new production and service calibrations for the Electronic Control Module (ECM) and Injector Drive Module (IDM) of the Diamond Logic™ Engine Control II.
Belt Wear On International VT 365, T 444E, DT 466, and 530 Engines
Procedure for containment of injector hold down snap rings during removal of fuel injector assembly.